LED marquee mod

by Vanessa Dannenberg

This mod provides set of alphanumeric LED marquee panels, controlled by Mesecons' Digilines mod.

Simply place a panel, right-click it, and set a channel.

Then send a character, a string, or one of several control words to that channel from a Mesecons Lua Controller and the mod will try to display it. The panels use the standard 7-bit ASCII character set (with a few alterations).

A single character will be displayed on the connected panel. A numeric message (i.e. not a string) will display the first digit on the connected panel.

Strings will be displayed using all panels in a lineup, so long as they all face the same way, starting from the panel the Lua Controller is connected to, going left to right. The other panels in the line do not need to be connected to anything - think of them as being connected together internally. Only the panel at the far left need be connected to the Lua Controller.

The string will spread down the line until either a panel is found that faces the wrong way, or has a channel that's not empty/nil and is set to something other than what the first is set to, or if a node is encountered that is not an alpha-numeric panel at all.

Panels to the left of the connected one are ignored (unless they, too, have their own connections).

You can also stack up a wall of LED panels, of any horizontal and vertical amount. If you then set a channel on the upper left panel, leave the others un-set, and connect a LuaController to it via digilines, the whole wall of panels will be treated as a multi-line display.

Long strings sent to that channel will be displayed starting at the upper-left and working from left to right, top to bottom, wrapping from line to line as appropriate (similar to printing to a shell terminal).

As with a single line, printing continues from node to node until the program either finds a panel with a different non-empty channel than the first one, or if it finds a panel that's facing the wrong way.

If the program finds something other than a panel, it wraps to the next line. If it finds something other than a panel twice in a row, that signals that text has wrapped off of the last row, and printing is cut off.

Lines of panels don't need to be all the same length, the program will wrap as needed, with the left margin always being aligned with the panel the LuaController is connected to.

Strings are trimmed to 1 kB.

Panels are not erased between prints.

Any unrecognized symbol or character, whether part of a string or singularly is ignored, except as noted below.

This mod uses the full ISO-8859-1 character set (see https://en.wikipedia.org/wiki/ISO/IEC_8859-1 for details), plus a bunch of symbols stuffed into the empty 128-159 range that should be useful on a marquee:

• 128,129: musical notes
• 130-140: box drawing glyphs
• 141-144: block shades
• 145-152: arrows
• 153-156: explosion/splat
• 157-159: smileys

The panels also respond to these control messages:

• the keywords "off", "colon" and "period" translate to a blank space, ":", and ".", respectively (they're leftover from the nixie tubes fork, but might be useful anyway)
• "del" is mapped to character #127, a square with an X in it.
• "allon" is mapped to character #144, the full/all-on block graphic.
• "cursor" or character code 31 will display a short, thick, flashing line at the bottom of the panel.
• "off_multi" turns all panels in a lineup off
• "allon_multi" turns on all LEDs of all panels in a lineup.

A byte value of 0 to 27 will change colors (i.e. string.char(0 to 27) ). Color values 0 to 11 are:

Red (0), orange, yellow, lime, green, aqua, cyan, sky blue, blue, violet, magenta, or red-violet (11)

Colors 12 to 23 are the same as 0 to 11, but lower brightness.

Colors 24 - 27 are white, light grey, medium grey, and dim grey.

The left-most/"master" panel will remember the last color used, and defaults to red.

A byte value of 28 will act as a line feed (I would have used 10, but that's a color code :-P )

A byte value of 29 signals a cursor position command. The next two byte values select a column and row, respectively. The next character after the row byte will be printed there, and the rest of the string then continues printing from that spot onwards.

You can use "get" and "getstr" to read the one character from the connected panel. These messages will not read the other panels in the lineup.

All panels emit a small amount of light when displaying something.

The panels only mount on a wall.