moretrees/default_settings.txt

131 lines
6.3 KiB
Plaintext
Raw Normal View History

-- Global configuration variables
-- Enable the various kinds of trees.
moretrees.enable_apple_tree = true
moretrees.enable_oak = true
moretrees.enable_sequoia = true
moretrees.enable_palm = true
moretrees.enable_date_palm = true
moretrees.enable_cedar = true
moretrees.enable_rubber_tree = true
moretrees.enable_willow = true
moretrees.enable_acacia = true
moretrees.enable_birch = true
moretrees.enable_spruce = true
moretrees.enable_jungle_tree = true
moretrees.enable_fir = true
moretrees.enable_beech = false
-- set this to true to make moretrees spawn saplings at mapgen time instead
-- of fully-grown trees, which will grow into full trees after a very short
-- delay. This reduces mapgen lag in some situations.
moretrees.spawn_saplings = false
-- Set this to true to allow defining stairs/slabs/etc. If Moreblocks is
-- installed, this will use that mod's Stairs Plus component. Otherwise, it
-- will use the default stairs mod in minetest_game, if present
moretrees.enable_stairs = true
-- Set this to true if you want the plantlike drawtype for leaves, which
-- improves some peoples' framerates without resorting to making leaf nodes opaque.
-- Affects default leaves and default jungle leaves also.
moretrees.plantlike_leaves = false
-- Enable this if you want moretrees to redefine default apples so that they
-- fall when leaves decay/are dug.
moretrees.enable_redefine_apple = true
-- Set this to true to enable leaf decay of all trees except the default ones.
moretrees.enable_leafdecay = true
-- various related settings to configure leaf decay.
moretrees.leafdecay_delay = 2
moretrees.leafdecay_chance = 5
moretrees.leafdecay_radius = 5
moretrees.palm_leafdecay_radius = 10
-- Change these settings if you want default trees to be gradually cut down
-- above the elevation where firs normally generate.
moretrees.firs_remove_default_trees = false
moretrees.firs_remove_interval = 2
moretrees.firs_remove_chance = 150
-- Cocos palm settings
moretrees.coconuts_regrow = true
moretrees.coconuts_convert_existing_palms = true -- Converting existing palm trees will make coconuts regrow on them as well
-- Else, they will only regrow on newly-spawned palms
-- However, conversion is not an exact science, and although an attempt is
-- made to detect whether a trunk belongs to an actual palm, some coconut trunks
-- and some coconuts may be incorrectly converted.
moretrees.coconut_flower_interval = 59
moretrees.coconut_flower_chance = 67
moretrees.coconut_grow_interval = 2 * moretrees.coconut_flower_interval * moretrees.coconut_flower_chance
-- Actual interval will randomly vary between 67% and 133% of this value
-- 2 * 59 * 67 ~ 2 hours. So flowers become coconuts in about 6 hours
moretrees.coconut_item_drop_ichance = 10 -- inverse probability of ripe coconuts dropping as items (instead of disappearing)
-- Date palm settings
-- Suggested configuration alternatives:
-- - Dates grow only when pollinated:
-- - Set dates_regrow_pollinated to true
-- - Set dates_regrow_unpollinated_percent to 0
-- - Dates grow without pollination. Pollination disabled:
-- - Set dates_regrow_pollinated to false
-- - Set dates_regrow_unpollinated_percent to some larger positive value, e.g. 95
-- - Dates grow, but more and faster if male flowers are nearby
-- - Set dates_regrow_pollinated to true
-- - Set dates_regrow_unpollinated_percent to some small positive value, e.g. 33
-- - Optional but recommended: Reduce the pollination distance, e.g. to 30
-- Note that it should not be necessary to disable pollination for performance
-- reasons. A lot of effort has gone into ensuring that date growing will not cause lag.
--
-- If lag is suspected, use the chat command '/dates_stats' to obtain the male dates
-- search time, as well as the counts of total number of searches requested and the
-- number of searches actually performed.
moretrees.dates_regrow_pollinated = true -- Enable pollination. If enabled, male trees are required for dates to grow.
-- If disabled, dates_regrow_unpollinated_percent must be non-zero for dates to regrow.
moretrees.dates_regrow_unpollinated_percent = 0 -- Percentage of female dates becoming dates without being pollinated.
-- If 0, dates_regrow_pollinated must be enabled for dates to grow.
moretrees.dates_female_percent = 57 -- Ratio of female to male trees - tune this to improve # of generated trees that actually bear fruit
-- ~57% gives near optimal results for groups of 3 random trees, while it is only slightly suboptimal
-- for groups of 2 and 4 random trees (~2% less fruit than optimal).
-- Optimal values per group size: 2: 50%, 3: 57.78%, 4: 63%, 5: 66.9%, 6: 69.9%, [...], 12: 79.8%
-- So 57% is optimal for small groups of trees. As larger groups have more female palms anyway, a
-- less than optimal proportion of female to male trees is not a problem.
moretrees.dates_pollination_distance = 120
moretrees.dates_blossom_search_time_treshold = 1000 -- If average male blossom search time (in microseconds) exceeds this, start limiting the search load.
moretrees.dates_blossom_search_iload = 10 -- Inverse fraction of CPU time that male blossom searching search may consume.
-- As searching a large area (radius: dates_pollination_distance/3 per attempt) can cause lag,
-- this limits the search frequency server-wide so that the impact on server lag is minimised
-- For personal servers, this can be set lower, or even to 1 or 0 (0 disables load limiting).
-- Obtain the current average search time using /dates_stats
moretrees.dates_flower_interval = 59
moretrees.dates_flower_chance = 181
moretrees.dates_grow_interval = 2 * moretrees.dates_flower_interval * moretrees.dates_flower_chance
-- As date palms have a high yield, don't grow dates too fast
-- The actual interval will vary randomly between 67% and 133% of this value.
-- 2 * 59 * 181 ~ 6 hours. So by default flowers become dates in about one (human) day.
moretrees.dates_item_drop_ichance = 10 -- inverse probability of ripe dates dropping as items (instead of disappearing)
-- Sapling settings
moretrees.sapling_interval = 500
moretrees.sapling_chance = 20
-- If this variable is set to true, drop leaves out as entities during leaf
-- decay, rather than just disappearing them.
moretrees.decay_leaves_as_items = false