65 lines
3.2 KiB
HTML
65 lines
3.2 KiB
HTML
<!-- Generate `description.html` from this by using `$ md2html -o description.html description.md`. -->
|
|
<p>The Microcontroller is a semi-advanced programmable component with a persistent
|
|
256 bit EEPROM memory.</p>
|
|
<p>Warning: This device is largely considered deprecated and might contain bugs. It
|
|
is recommended to use a Luacontroller instead.</p>
|
|
<p>Detailed documentation can be found below:</p>
|
|
<ul>
|
|
<li>The Microcontroller's code is executed whenever any of the following events
|
|
happens:<ul>
|
|
<li>The Microcontroller is programmed. In this case the EEPROM and ports are all
|
|
reset to <code>0</code> before.</li>
|
|
<li>An incoming signal changes its state.</li>
|
|
<li>An <code>after</code> event happens (see command <code>after</code> below).</li>
|
|
</ul>
|
|
</li>
|
|
<li>There are 4 I/O ports (ABCD) and 256 EEPROM bits (1 to 256).</li>
|
|
<li>The code consists of a sequence of commands.</li>
|
|
<li>Everything after <code>:</code> is a comment.</li>
|
|
<li>Strings are enclosed in <code>"</code>s.</li>
|
|
<li>Spaces and tabs outside of strings are ignored.</li>
|
|
<li>Basic command syntax:<pre><code> command_name`(`param1`,` param2`,` ...`)`
|
|
</code></pre>
|
|
</li>
|
|
<li>Commands:<ul>
|
|
<li><code>if(condition) commands [> else_commands];</code>:
|
|
Evaluates the given condition and takes the corresponding branch.
|
|
The else branch is optional (as indicated by the <code>[</code> and <code>]</code>). The <code>></code> is part
|
|
of the syntax and indicates the start of the else branch. The <code>;</code> marks the
|
|
end of the if command.</li>
|
|
<li><code>on(port1, port2, ...)</code>:
|
|
Sets the given ports to <code>1</code>.</li>
|
|
<li><code>off(port1, port2, ...)</code>:
|
|
Sets the given ports to <code>0</code>.</li>
|
|
<li><code>print("string" or codition, ...)</code>:
|
|
Evaluates the conditions and prints the concatenation of all params to stdout
|
|
(only useful in singleplayer).</li>
|
|
<li><code>after(time, "more commands")</code>:
|
|
Executes the commands in the string after the given time in seconds.
|
|
There can only be one waiting <code>after</code> event at once.
|
|
Warning: This is not reliable, ie. <code>minetest.after</code> is used.</li>
|
|
<li><code>sbi(port_or_eeprom, condition)</code>:
|
|
Evaluates the condition and sets the port or EEPROM bit to the resulting value.
|
|
Note: EEPROM indices don't use <code>#</code> here, ie. it's <code>sbi(1, #2)</code>, not <code>sbi(#1, #2)</code>.</li>
|
|
</ul>
|
|
</li>
|
|
<li>Conditions (sorted by descending precedence; they are all evaluated from left
|
|
to right):<ul>
|
|
<li><code>0</code>, <code>1</code>: constant</li>
|
|
<li><code>A</code>, ..., <code>D</code>: value of a port. Takes writes that already happened during the
|
|
current execution into account.</li>
|
|
<li><code>#1</code>, ..., <code>#256</code>: value of an EEPROM bit. Takes writes that already happened
|
|
during the current execution into account.</li>
|
|
<li><code>!condition</code>: negation (can only be applied once, ie. not <code>!!1</code>)</li>
|
|
<li><code>condition1 = condition2</code>: XNOR (equality)</li>
|
|
<li><code>condition1 op condition2</code> where <code>op</code> is one of:<ul>
|
|
<li><code>&</code>: AND</li>
|
|
<li><code>|</code>: OR</li>
|
|
<li><code>~</code>: XOR (inequality)</li>
|
|
</ul>
|
|
</li>
|
|
<li>Note: Explicit precedence using parentheses is not supported.</li>
|
|
</ul>
|
|
</li>
|
|
</ul>
|