pipeworks/settingtypes.txt

#Enable pipes.
pipeworks_enable_pipes (Enable Pipes) bool true

#Enable autocrafter.
pipeworks_enable_autocrafter (Enable Autocrafter) bool true

#Enable deployer.
pipeworks_enable_deployer (Enable Deployer) bool true

#Enable dispenser.
pipeworks_enable_dispenser (Enable Dispenser) bool true

#Enable node breaker.
pipeworks_enable_node_breaker (Enable Node Breaker) bool true

#Enable teleport tube.
pipeworks_enable_teleport_tube (Enable Teleport Tube) bool true

#Enable pipe devices.
pipeworks_enable_pipe_devices (Enable Pipe Devices) bool true

#Enable redefines.
pipeworks_enable_redefines (Enable Node Redefines) bool true

#Enable sorting tube.
pipeworks_enable_mese_tube (Enable Sorting Tube) bool true

#Enable detector tube.
pipeworks_enable_detector_tube (Enable Detector Tube) bool true

#Enable digiline detector tube.
pipeworks_enable_digiline_detector_tube (Enable Digiline Detector Tube) bool true

#Enable mesecon signal conducting tube.
pipeworks_enable_conductor_tube (Enable Conductor Tube) bool true

#Enable digiline signal conducting tube.
pipeworks_enable_digiline_conductor_tube (Enable Digiline Conductor Tube) bool true

#Enable accelerator tube.
pipeworks_enable_accelerator_tube (Enable Accelerator Tube) bool true

#Enable crossing tube.
#It sends all incoming items to the other side, or if there is no other tube, it sends them back.
pipeworks_enable_crossing_tube (Enable Crossing Tube) bool true

#Enable vacuum tube.
#It picks up all items that lay around next to it.
pipeworks_enable_sand_tube (Enable Vacuum Tube) bool true

#Enable mese vacuum tube.
#It's like the normal vacuum tube with the
#differance that you can set the radius up to 8 nodes.
pipeworks_enable_mese_sand_tube (Enable Mese Vacuum Tube) bool true

#Enable one way tube.
#It sends items only in one direction.
#Use it to drop items out of tubes.
pipeworks_enable_one_way_tube (Enable One Way Tube) bool true

#Enable high priority tube.
#It has a very high priority and so, on crossings, the items will
#always go to it if there are multible ways.
pipeworks_enable_priority_tube (Enable High Priority Tube) bool true

#Enable lua controlled tube.
#It is comparable with mesecons luacontroller.
pipeworks_enable_lua_tube (Enable Lua controlled Tube) bool true

#Enable cyclic mode.
pipeworks_enable_cyclic_mode (Enable Cyclic Mode) bool true

#Drop on routing fail.
pipeworks_drop_on_routing_fail (Drop On Routing Fail) bool false

#Delete item on clearobject.
pipeworks_delete_item_on_clearobject (Delete Item On Clearobject) bool true

#Use real visible entities in tubes within active areas.
#When disabled, tubes are made opaque.
pipeworks_use_real_entities (Use Real Entities) bool true

#Target interval between tube entity steps.
#A high value may cause issues with tube entity visuals.
#A value 0.2 or above may cause issues with accelerator tubes.
pipeworks_entity_update_interval (Entity Update Interval) float 0 0 0.8

# Use the default rules from the digilines mod.
# If enabled the following devices will connect to digiline networks in the vertical direction:
# digiline filter injector, deployer, dispenser, node breaker, autocrafter
# If disabled, the devices will not be able to send or recieve digiline signals from the top
# or bottom faces, regardless of the node rotation. This breaks expected behavior with digiline
# conducting tubes, so it is recommended to enable this option unless you have specific builds
# that make use of the lack of vertical digiline connectivity and those are more important to you.
enable_vertical_digilines_connectivity (Use the default rules from the digilines mod) bool true

# if set to true, items passing through teleport tubes will log log where they came from and where they went.
pipeworks_log_teleport_tubes (Log Teleport Tubes) bool false

# Behavior of print() inside a lua tube. By default, this emits a message into actionstream.
# Set it to noop if you wish to disable that behavior.
pipeworks_lua_tube_print_behavior (Behavior of print in Lua Tube) enum log log,noop